Tags
Instrumentation, Systems & Automation

Advanced diagnostics added to level transmitters

Endress+Hauser has added Heartbeat Technology to its Micropilot FMR5X free-space radar and FMP5X Levelflex guided radar level transmitters.

Heartbeat Technology is an on-board diagnostics and instrument verification system that continuously monitors the status of mechanical, electromechanical and electronic components in the sensor, and sends alerts when it detects a problem. Alerts are sent in accordance with NAMUR recommendation NE 107 and are displayed at the device. Alerts include “Out of specification,” “Maintenance required,” “Device failure” and “Device OK.” The built-in diagnostics can detect process problems, such as build-up or foam before failure occurs.

Heartbeat Technology is also able to perform device verification in accordance with requirements of the pharmaceutical, food and beverage, oil & gas, chemical and other industries. Such requirements call for level instruments to be removed and calibrated unless in-situ verification proves the device is operating properly. 

During verification, Heartbeat Technology compares internal components with their reference values, thereby determining the device status. Verification produces a pass or fail statement, depending on whether the assessment is positive or negative, and generates a verification report in compliance with quality, safety and regulatory requirements, and meeting the needs of agency auditors. 

Verification information, reports, diagnostics alerts and instrument data can be viewed at the control and monitoring system, or via a web browser running on a PC, tablet or smartphone. 

Heartbeat Technology reduces the need for calibrations requiring the removal of instruments from the process; reduces the need for maintenance personnel to perform on-site instrument checks; immediately alerts operators when an instrument requires service; and provides diagnostics functions to describe problems so technicians know what they are dealing with before they go to the field. 

The Micropilot FMR5X series of free-space radar level transmitters provide accuracy up to ±2mm  for level measurement of liquids and ±4mm for bulk solids products in the pharmaceutical, food and beverage, oil & gas, chemical and other industries.  Multiple FMR5X transmitters can be installed in the same tank without interference among them because the transmitter pulses are statistically coded.

FMR5X instruments can be used to measure level or volume with a built-in 32-point strapping table. The liquids can be measured in metal or plastic tanks, stilling wells, bypass chambers or other vessels up to 131 feet high with standard units, or 197 feet with an enhanced dynamics option. The instrument can also be used to detect minimum or maximum levels to prevent overfilling or empty tanks, in addition to continuous monitoring of the level. 

Company Info

Latest News

Tags
Offshore Technology

Dresser-Rand supplies compressor trains for deepwater BP project

 – Copyright BP Images

The Dresser-Rand business, part of Siemens Power and Gas Division, received an order from BP to provide rotating equipment for the Mad Dog 2 project in the deepwater Gulf of Mexico. The scope of supply comprises two DATUM compressor trains driven by Siemens electric motors for export gas service. The equipment is scheduled to ship in 2018, with oil production of the platform expected to begin late in 2021.

Read More

Sponsored Content

Volvo’s Award-Winning CoPilot Interface – Make Every Operator Your Best Operator

With the Volvo award-winning Co-Pilot on-board interface, operators can set up projects with ease, get real-time job information and get more done with less rework. Use Co-Pilot for a multitude of applications, including Load Assist for wheel loaders, Compact Assist for Asphalt with Density Direct™, and Dig Assist for excavators. Learn more about how Co-Pilot can make your jobs more efficient, and more profitable. 

Watch and learn more

Tags
Asset Management

Bearings boost turboexpander performance and longevity

Turboexpanders are the heart of cryogenic process cycles everywhere, including air separation and gas liquefaction systems. At the same time, the component that is critical to those processes and is essential to trouble-free system efficiency is the bearing that supports the shaft linking a turboexpander’s barbell-shaped expansion and compression wheel assembly.

Read More

Tags
Environmental
Industry News

Carbon emission cut by 2040 within reach but requires cooperation

Reduction in coal energy is one part of a successful climate strategy going forward, according to the ETC.

Governments, investors and businesses must seize the opportunity to halve global carbon emissions by 2040 while ensuring economic development and energy access for all, but they must act now to accelerate clean electrification, decarbonization beyond power and energy productivity improvement, says the Energy Transitions Commission (ETC). 

Read More

Tags
Power Systems

Rolls-Royce and MTU products to be presented at OTC

The MTU Series 4000 T95 Tier 4 final engine will be on display in the Rolls-Royce / MTU exhibit at OTC 2017.

Rolls-Royce will feature the latest technologies from MTU and Rolls-Royce on Booth #2261 for onshore and offshore oil and gas applications at the 2017 Offshore Technology Conference (OTC) from May 1 – 4 at NRG Park in Houston, Texas. The exhibit will feature the MTU Series 4000 Bi-Fuel Kit, the 12V 4000 T95 EPA Tier 4 engine and advanced technology for next generation vessels from Rolls-Royce. The MTU brand is part of Rolls-Royce Power Systems.

Read More

Tags
Drilling & Production
Offshore Technology

Companies combine expertise on challenging engineering and hardware support services

Trendsetter Engineering and Add Energy have combined expertise to provide engineering and hardware support services to the industry’s most challenging problems. The companies have recently been awarded a contract to supply engineering expertise and access to Trendsetter’s patented Relief Well Injection Spool (RWIS) in support of an operators’ drilling campaign on a newly sanctioned field development. 

Read More

Tags
Industry News
Offshore Technology

Oil recovery system powered by wind shows potential in testing

The DNV GL-led joint industry project, WIN WIN (WINd powered Water INjection), has completed its first phase and determined that wind power could be used to power offshore water injection. The project is currently moving into its second phase, which includes refining and testing the electrical systems, and investigating possibilities for broader applications. The project consists of four partners: DNV GL, ExxonMobil and ENI Norge – all part of the first phase – and the Norwegian Research Council – a new participant for this second phase. 

Read More

Tags
Instrumentation, Systems & Automation

Load pins able to measure up to 30,000 pounds

The OMEGA LCP Series is a compact load pin with the ability to measure up to 30,000 lbs. These specially designed load pins are ideal for tension and compression measurements and can easily replace existing shear pins, clevis bolts, clevis pins, shear axles and many other types of pinned joints. The LCP Series can be applied on clevis pin shackles, loading cranes, lifting fittings, hydraulic presses, sprockets, pulley axles and more. The LCP load pins offer 0.50% high accuracy, an all stainless steel construction and a standard connector. 

Read More