Tags
Drilling & Production

In-Viro-Drum effective in cleaning up oil spills

When environmental damage, and the health and safety of employees or local residents are at risk, rapid response and recovery is the only choice. The AB-CAN In-Viro-Drum is a spill recovery unit that has been used successfully in a wide variety of applications where failure is not an option. First-time users are always amazed by the suction power demonstrated by the In-Viro-Drum, the company says. The design of The In-Viro-Drum makes each unit compact and easy to transport. It can be mounted on light trucks, light tandem trailers, ATVs, light water vessels, skids, or flown by helicopter to remote spills. In most applications, a single operator is all that is required.

The hazardous spill management capabilities makes the In-Viro-Drum an investment that brings an immediate return by reducing or eliminating risk. Any liquid, regardless of its viscosity, slurries, powders, or small solid particulates can be quickly “sucked up” by the unit and deposited into container vessels. A variety of containment vessels, including 45-gallon drums, can be used to deposit waste ready for safe disposal.

Company Info

  • ABCAN Environmental Inc.

    5562 56 Avenue SE
    Calgary , AB
    CA , T2C 3X6

    ABCAN environmental cleanup technology is being used in the most demanding applications.  The primary market is in Canadian industries, municipalities, coast guard and military which demand rugged performance. However, ABCAN environmental products are ideal for use around the world due to their size, adaptability, and easy mobility. ABCAN has grown significantly due to its reputation for solving difficult hazardous and other spill recovery problems.

    Read more

Related News

Tags
Drilling & Production

Eaton’s new CMA advanced mobile valve with independent metering helps manufacturers deliver next-generation machine performance

CMA 90 Advanced Mobile Valve.

Power management company Eaton has announced the new CMA Advanced Mobile Valve with Independent Metering, which offers manufacturers nearly endless possibilities to differentiate machine capabilities. The CAN-enabled electrohydraulic mobile valve features on-board electronics and sophisticated software algorithms, which surpasses industry standards for intelligence, capabilities, dynamics and control.

Read More

Tags
Drilling & Production

Gorman-Rupp 6500 Series Standard Horizontal End Suction Centrifugal Pumps

Gorman-Rupp Offers NEW 6500 Series(TM) Standard Horizontal End Suction Centrifugal Pumps (PRNewsFoto/Gorman-Rupp)

Gorman-Rupp has introduced a new line of horizontal end suction centrifugal pumps. The new 6500 Series line offers solids and water handling end suction centrifugal pumps based on the proven technology of the Prime Aire and Prime Aire Plus models.

Read More

Tags
Drilling & Production

Eaton’s Variable Speed Drive Pump Solution Enables Significant Energy Savings in Industrial Machinery

Eaton’s Variable Speed Drive Pump Solution Enables Significant Energy Savings in Industrial Machinery

Power management company Eaton has announced a new variable speed drive (VSD) pump solution that can provide up to 70 percent energy savings for equipment in the machine building, manufacturing, oil and gas and marine industries, depending on the machine duty cycle. The industrial pump solution, available in open- or closed-loop motion control configurations, reduces operational costs by allowing quieter machine operation, reducing or eliminating cooling needs and allowing for pump downsizing.

Read More

Tags
Drilling & Production

Blackmer SMVP Series Pumps Feature Operational Advantages for Achieving the Full Containment of Chemicals

Blackmer, part of PSG, a Dover company that manufactures positive displacement and centrifugal pumps, and reciprocating compressor technologies, has announced that its SMVP Series Seal-Less Mag-Drive Sliding Vane Pumps feature a design that enables them to meet the need for zero leakage when handling expensive, hazardous and hard-to-seal fluids.

Read More

Tags
Drilling & Production

Rubber-coated parts reduced wear for Midwest frac sand producer

Rubber-coated parts reduced wear for Midwest frac sand producer

GIW Industries announced the success of a pumping solution that doubled the lifespan of wear parts in the operations of a major frac sand producer in the U.S. Midwest. The highly-abrasive frac sand mining process causes extreme wear, and pump parts typically need replacement every two years. However, with installation of GIW’s rubber-coated parts, wear life of the pump’s wet-end parts was extended to 3.75 years, when the parts were replaced during scheduled maintenance.

Read More

Tags
Drilling & Production

Full Containment Capabilities of PSG Seal-Less Pump Technologies To Be Highlighted At ACHEMA Show

Full Containment Capabilities of PSG Seal-Less  Pump Technologies To Be Highlighted At ACHEMA Show

PSG, a Dover company and a global leader in the manufacture of pumps, systems and related flow-control technologies, is pleased to announce that it will be displaying a full array of seal-less pump technologies in Hall 8.0, Stand D37 at the upcoming ACHEMA Show. ACHEMA is the world’s largest trade show for the chemical-processing industry.

Read More

Tags
Drilling & Production

OPW Engineered Systems Releases LQC Series Quick Couplings

OPW Engineered Systems Releases LQC Series Quick Couplings

OPW Engineered Systems, part of OPW's Fluid segment within Dover Corporation, has launched the LQC Series Transfer Loading Safety Quick Coupling under its Hiltap brand. The patented design of the LQC (Locking Quick Connect) Series automatically prevents accidental disconnects when pressure is in the line. Plus, the LQC's advanced engineering and rugged durability allow the LQC to safely connect fluids for a wide range of temperatures and pressures – in-plant, through plant and out-of-plant.

Read More

Tags
Drilling & Production

Design guidelines in development for concrete coatings

Design guidelines in development for concrete coatings

With submarine pipelines increasing in diameter and extending into deeper waters and more challenging environments, design requirements for concrete weight coating do often not meet current needs. The result is inconsistent safety margins and potentially expensive overdesign and stringent installation requirements. DNV GL has now kicked off the first phase of a joint industry project (JIP) to address these issues and improve the understanding of pipeline concrete behaviour. The aim is to develop a design guideline that complements current pipeline codes and standards. The JIP is still open for participants.

Read More