​When To Replace Forklift Forks

The forklift fork is often overlooked and under-inspected. Many are unaware of how often one should inspect their forks, and how to inspect them. Federal law (OSHA Standards 29 CFR 1910.178) mandates that forklift forks which see around-the-clock use should be inspected on a per-operation basis. As part of a pre-operation inspection, forklift forks should ideally be inspected for signs of cracks, bends, excessive wear or damage to either the fork tine or the positioning lock when using an ITA mounted fork.

What to look for:

1. Excessive wear to the forks
Forklift forks decrease in thickness over time due to normal wear. However, any wear to the fork over 10 percent of the total thickness is considered excessive. Forks that show this amount of wear should be replaced.

2. Fractures due to stress or collision
Be sure to inspect the forks closely for fractures and gouges. The fork heel and parts of the fork closest to the machine typically receive the most wear. Even small cracks and gouges are signs forks need to be replaced.

3. Damage to the fork tip
Since fork tips are usually the first part of the fork to come in contact with material, excessive wear or damage to the tips is a clear indicator the forks should be replaced.

4. Any bends or uneven surfaces on the fork
All forks are delivered with a 90 degree angle from the shank to the blade. If any bend or uneven surface is detected on either the blade or shank, the fork(s) need replacing.

5. Difference in fork blade height
A difference in the height of each fork blade should stay within 3 percent of the fork length. Therefore if the forks in question are 42 inches long the allowable difference in fork height would be 1.26 inches. Any difference in fork height beyond 1.26 inches is a sign that both forks need to be replaced.

6. Wear or damage to the fork hook
Noticeable wear, crushing, pulling, and other deformities are signs that the fork hooks need to be replaced. Furthermore, if the wear to the hook is causing an excessive amount of distance between the fork and the carriage, the hook(s) should be replaced.

7. Wear or damage to positioning lock
If a positioning lock is no longer capable of locking completely due to wear the forks should immediately be removed from duty until the part is replaced. Operating without a fully functional positioning lock is a safety hazard and illegal.

When it does come time to replace forklift forks here are some common questions.
1. Can a single fork be replaced or should they be replaced in pairs?
While only a single fork might show signs of excessive wear or damage, it is not safe to replace only one fork. It is highly recommended forks be replaced only in pairs to ensure equal performance. Having two different forks with unique amounts of wear and disproportionate hourly usage is provides a number of safety concerns. "Replacing just one fork may seem like a good idea, but can actually lead to serious safety violations." says Terry Melvin, CEO of Arrow Material Handling Products.

2. Is it ok to make custom repairs or modification to the forks?
It is typically recommended that only the fork manufacturer make repairs or modifications to ensure forks meet safety standards. Always contact your fork provider first when in need of modification.

3. How do I determine replacement fork quality?
Forks made from high quality boron-carbon alloy high strength steel are rated 20% stronger than those made with 40CR. In addition, forks that are fully immersed into industrial heat treatment ovens and cooling pools are the most durable. Premium quality forklift forks should meet or exceed all ANSI/ITSDF and ISO standards.

Helpful Links

- OSHA's pre operation forklift checklist and fork can be found at https://www.osha.gov/dte/libra...
- OSHA's guidelines on fork wear can be found at https://www.osha.gov/SLTC/etoo...
- Arrow Material Handling Products' Fork Quality Standards http://www.arrowmhp.com/pdfs/F...

This article was submitted by Arrow Material Handling Products.

Company Info

Latest News

Tags
Industry News
Pipelines

TransCanada's Topolobambo project goes into service in Mexico

TransCanada's Topolobambo project goes into service in Mexico

TransCanada Corporation  announced its Topolobampo Pipeline project has been placed into service in northern Mexico, providing capacity for 670 million cubic feet of natural gas per day to markets in the states of Chihuahua and Sinaloa. The project represents an investment of approximately US$1.2 billion and provides the upstream interconnection with the company's Mazatlan Pipeline.

Read More

Tags
Instrumentation, Systems & Automation

Hand-held combustion emissions analyzer

Hand-held combustion emissions analyzer

The E1500 Hand-Held Combustion Emissions Analyzer from E Instruments is a new, rugged unit with the ability to measure CO & O2 from high efficiency & condensing boilers, burners, engines, turbines, kilns, furnaces, incinerators and other industrial combustion processes.  Featuring a new large COLOR display and expanded internal memory, the E1500 lets you easily see and save your sample data without worrying about running out of memory. The E1500 also features pre-calibrated, field replaceable sensors which allow for easy diagnostics and replacement to reduce "down-time" and costly repair charges.

Read More

Tags
Industry News

Vertex Resource acquires Three Star Trucking

Vertex Resource acquires Three Star Trucking

Vertex Resource Group Ltd. has acquired Three Star Trucking Ltd., an environmental service company providing fluid hauling service, pressure truck services, hot oilers and combo vac services throughout western Canada on July 12th, 2018. The acquisition of Three Star will add over 270 pieces of equipment to Vertex's fleet, making the company's fleet one of the largest in operations serving Saskatchewan, the Montney, and the Duvernay resource plays of Alberta and British Columbia. 

Read More

Tags
Asset Management

Baker Hughes, SGS agree on joint deployment of corrosion management solution

Baker Hughes, SGS agree on joint deployment of corrosion management solution

SGS and Baker Hughes, a GE company, announced a Strategic Alliance Agreement (SAA) for the joint deployment and commercialization of BHGE's real-time software and sensor-based Predictive Corrosion Management (PCM) solution. Leveraging the capability of the Industrial Internet of Things (IIoT), PCM will enable asset owners to increase their ability to monitor their facilities, and detect and predict corrosion issues using real-time data powered by BHGE's ultrasonic sensing technology and advanced analytics. 

Read More

Tags
Drilling & Production
Industry News

Petroteq to test equipment for non-conventional oil production

Petroteq Energy Inc., a company focused on the development and implementation of proprietary technologies for the energy industry, announced an agreement with Cavitation Technologies, Inc., a company providing highly scalable and cost-effective solutions to various fluids processing industries. The companies have entered into a licensing agreement to test its equipment during oil production for workflow efficiencies and to lower its cost of production obtained through Petroteq's oil sands extraction process.  

Read More

Tags
Industry News

Painted Pony receives encouraging results from Lower Montney test wells

Painted Pony receives encouraging results from Lower Montney test wells

Painted Pony Energy Ltd. has announced results from two recent Lower Montney wells drilled on the northern edge of the South Townsend block. Preliminary results indicate production levels higher than Painted Pony management's Townsend type curve and include higher liquid yields compared to previous wells in the Townsend block. Painted Pony is encouraged by the results to-date and anticipates re-directing a portion of drilling activity within the existing 2018 development budget to better capitalize on these well results.

Read More

Tags
Industry News

Terex RT cranes handle desert drill site project without downtime

"Five months of continuous back-breaking work without any downtime," Nabors Drilling Manager David Siljeg succinctly puts it while summarizing how well the Terex RT 90 rough terrain crane performed at a work site in Abqaiq, Saudi Arabia. The crane lifted numerous components for drilling rigs, generators, and a power distribution and control centre at the oil field while enduring challenging environmental conditions.

Read More

Tags
Industry News

Paramount, Strath close sale of Resthaven/Jayar assets for $340 million

Paramount, Strath close sale of Resthaven/Jayar assets for $340 million

Paramount Resources Ltd. has closed the previously announced sale of its oil and gas properties and related infrastructure at Resthaven / Jayar in the Kakwa region to Strath Resources Ltd. Consideration received by Paramount totaled $340 million, and included $170 million in cash (subject to customary post-closing adjustments), 85 million Strath common shares and 10-year warrants to acquire 8.5 million Strath common shares. As a result, Paramount holds an approximate 16% equity interest (undiluted) in Strath and Jim Riddell, Paramount's President and Chief Executive Officer, has joined Strath's Board of Directors. The cash consideration received will be used to reduce outstanding indebtedness under Paramount's credit facility.

Read More

Tags
Industry News
Offshore Technology

Decommissioning Leadership Group meets to set strategy

Industry leaders have, this month, joined together to shape the future of decommissioning through the formation of the Decommissioning Leadership Group (DLG). Conceived and managed by Decom North Sea, the DLG held its inaugural meeting at The Chester Hotel in Aberdeen earlier in June with the mission to set out a strategy for leading the development of an efficient and effective oil and gas decommissioning sector.

Read More

Tags
Instrumentation, Systems & Automation

Harting introduces Han-Smart modular connectors

In launching the first Han-Smart modules, HARTING is bringing new, intelligent capabilities to the highly esteemed, customer configurable Han-Modular connector system. Until now, industrial connectors have been used exclusively as passive devices for carrying power, signal, data transmission and pneumatics - functions they continue to provide. However, with Han-Smart solutions, connectors can provide added value while beginning to evolve into active devices to serve the needs of future manufacturing. These three modules are just the beginning:

Read More