Oil & Gas Product News Logo

Tool tethers improve productivity and safety

Tool tethers improve productivity and safety

Correct tool tethering is a delicate balance of maximizing productivity while safely minimizing the incidence of tools dropped from aloft. Selecting the proper tether is based on tool weight and usage to provide effective tethering solutions that significantly improve productivity and safety.

In its rapid descent down the tower, a falling wrench can become an unguided missile that may seriously endanger everything and everyone below. It is a serious site safety issue. At best, the falling object will just increase maintenance costs by downtime spent retrieving and repairing the dropped tool. At worst, it will cause serious injury to personnel and significant damage to equipment. It is a situation that can be easily avoided by using a properly matched tool or instrument tether.

The safety engineers’ goal in correct tethering procedures is to make sure the tool, application and recoil/retraction force are in balance. Ideally, when the tool is extended for use, only minimal force should be necessary so as to prevent worker fatigue or in the reverse, cause a ”kick” when retracted. The challenge to the safety engineer is to provide a tether that is both friendly to the user and appropriate for the work environment. Equally important, the tether or lanyard must have ample safety margins, beyond the weight rating of the tether, to mitigate the drop force in the event of a dropped tool.

With such a high risk to workers’ safety, it’s unfortunate that very little has been published on the subject of tool and instrument tethering equipment and safety techniques. Here is a simplified guide to help you select tethers for tools weighing up to 25 pounds.

Step 1. Determine tool tether type based on tool weight and usage

The most common tool tethers and lanyards for tools up to 25 pounds generally fall into five categories: Retractable Lanyards; Wrist Lanyards; Personal Tethers, Personal Tethers with Anchor Strap and Anchored Tethers.

For tools up to two pounds, the following options are best:
• Retractable Lanyards provide an ultra-low profile to keep the tool close to the body. This is important for working in confined-space and/or when climbing is required. They are also ideal for multiple tether use.
• Wrist Lanyards are low-profile tethers that provide a short drop length for easy retrieval of a dropped hand tool.
• Personal Tool Tethers are best for single use tool that moves with the worker.
• Personal Tool Tether w/Anchor Strap for single use tool attached to a structure for additional security or ease of use.

For tools up to 15 pounds, the following options are best:
• Personal Tool Tethers are best for a single use tool that moves with the worker.
• Personal Tool Tether w/Anchor Strap for single use tool that is attached to a structure.
• Anchored Tether System that attaches a heavy tool (five pounds or more) to a structure.

For tools up to 25 pounds, the following options are best:
• Personal Tool Tether w/Anchor Strap for single use tool that is attached to a structure.
• Anchored Tether System that attaches a heavy tool to a structure.
Note: Generally, any tool over 5 pounds should always be anchored to a structure to transfer the “dropped tool” shock load from the person to the structure.

Step 2. Determine if tether is for single tool or multi-tool use

A Fixed Lanyard System is acceptable when you don’t need to remove a tool from the lanyard.

When easy tool change-out is required a Side Release Lanyard System or Carabiner Clip are the best options.

Step 3. Determine the tool attachment point

A) Tool has lanyard loop. Attach lanyard to loop.

B) Tool has large ends. Ends must be large enough to allow a lanyard to be looped and cinched securely without slipping off.

C) Tool has small ends or no lanyard loop. If tool does not have large enough ends (looped lanyard would slide off) or lacks a lanyard loop, you must attach a ring.

D) Tool modification. If none of the above works, the tool must be modified by a safety engineer or the tool manufacturer.

Conclusion
When choosing tethers, here are 9 points to keep in mind.

1. Choose your tethers based on all factors of use. There are thousands of tethering choices available from manufacturers specializing in tool, gear and instrument tethers to tool manufacturers.

2. When tool tethers are ordered without specifications beyond the weight of the tool, chances are good that the tether may not be appropriate. Unlike fall protection devices, there are no universal specifications governing tool tethers. As such, the safety engineer has no real basis for choosing proper tethers and may arbitrarily determine tether selection based solely on the weight of the tool, i.e. “I need a tether for a 3-lb tool.” Without additional specifications, this may be creating a potentially dangerous situation.

3. An improperly mated tool and lanyard can inherently lead to reduced productivity and exposure to injury.

4. Tethering heavy tools to a person (generally over 5 pounds), is a significant safety concern and safety engineers should instead consider using anchor tethers. Anchored tethering safely transfers the shock load produced by a dropped tool from the worker to the structure.

5. For very heavy tools (over 10 pounds), structure anchoring should be mandatory.

6. When choosing an “Anchored Tethering System” choose one that offers up to a 10-foot working length for maximum safety and efficiency.

7. Modular tethering systems offer the most options for safe tool tethering.

8. When employees are using a group of small hand tools (under 2 pounds) Quick Connect tethers offer easy tool change-out and avoid the entanglement danger of having multiple tethers.

9. Before you purchase a tool or instrument tethering system, make sure that the tethers and lanyards are dynamically load tested for the tool weight specified. Confirm that the tool tether weight ratings indicated have a safety margin beyond the break point so that the tether or lanyard can safely handle the shock load of a dropped tool or instrument.


 

Company info

500 South C. P. Avenue
Lake Mills, WI
US, 53551

Website:
hammerheadtrenchless.com

Phone number:
920-648-4848

Read more