Neptune, part of PSG, a Dover company, now offers the new NSP Series Solenoid Metering Pumps and NXP Series Stepper Motor-Driven Metering Pumps for chemical applications that require reliable and accurate dosing.
Advantage announces significant oil discovery at Progress, Alberta
Advantage Oil & Gas Ltd. reports that a significant Montney light oil pool has been discovered and appraised at Progress, Alberta, on the Corporation's 47 net section block of 100% owned lands. This discovery elevates the Progress asset to be a primary element of the Corporation's near-term liquids development program.
Advantage has drilled four successful Montney wells to date at Progress, with the most recent located at 16-36-76-10W6 demonstrating average production test rates over 2,100 boe/d (62% liquids). The 16-36 well was drilled to a measured depth of 5,268 meters with a lateral length of 2,867 meters. Following fracture stimulation using approximately 2 tonnes of sand per meter, the well was flowed-back on clean-up, then subjected to a 72-hour production test at the end of the operation. The test results were as follows:
- Production rates and pressure were increasing throughout as the well continued to clean up
- Average oil rate during the 72-hour test was 1,038 bbls/d (43 degree API oil)
- Average gas rate during the 72-hour test was 4.9 mmcf/d
- Recoverable natural gas liquids entrained in the gas were approximately 290 bbls/d based on the average gas rate during the 72-hour test, using Glacier Gas Plant recoveries
- Average flowing pressure during the 72-hour test was 5,168 kPa, increasing throughout
- H2S content averaged approximately 0.1>#/li###
Two of the previous three wells drilled at Progress were in the same layer (D3) and demonstrated similar combined oil/NGL yields. The 16-36 well was completed with an updated frac design which is considered by Advantage to be a significant factor contributing to the high liquids yield and overall productivity. The Progress lands were acquired over the last 5 years and appraisal began in 2017. The four wells delineate the entire Progress land block and confirm the extensiveness of the oil accumulation.
The 16-36 well was shut-in for equipping and tie-in on September 2. The asset will be tied-in to Advantage's 100% owned Glacier Gas Plant for gas processing and liquids extraction, making use of existing surplus plant capacity and an existing section of an unused Advantage pipeline. The tie-in and equipping of the wells are targeted for completion by November 2019.
The 16-36 well represents a major milestone in demonstrating that each of Advantage's land blocks (Glacier, Pipestone/Wembley, Valhalla and Progress) features high-quality resource with attractive economics in the current commodity price environment. With this top-tier result at Progress, the asset has become a key element of the Corporation's near-term liquids development plan and is viewed by Management as competitive with Pipestone/Wembley.
Successful Liquids Development Continues with Liquids Production Increasing to 3,300 bbls/d
The Corporation's focus on liquids development has resulted in liquids production more than doubling, from an average rate of 1,491 bbls/d in 2018 to over 3,300 bbls/d in August 2019. Condensate-rich wells at east Glacier and Valhalla have driven the recent growth. In addition, Advantage's first Pipestone/Wembley well is expected to be brought on-production during the second half of September 2019 in conjunction with the commissioning of Tidewater's Pipestone gas plant.
Advantage continues to monitor natural gas price volatility and reduce gas production during times of low prices, consistent with our previously announced production strategy (see press release August 1, 2019). The Corporation is also proactively managing its capital spending plans to maintain a strong balance sheet and preserve financial flexibility.
More from Drilling & Production
Baker Hughes, a GE company announced that the Baker Hughes international rig count for August 2019 was 1,138, down 24 from the 1,162 counted in July 2019, and up 130 from the 1,008 counted in August 2018. The international offshore rig count for August 2019 was 244, down 11 from the 255 counted in July 2019, and up 32 from the 212 counted in August 2018.
SPX FLOW has a long history in supplying portable pump technology to the oil and gas industry. Some of its models have proved so successful and popular that they have been around (upgraded and improved) for nearly 50 years and continue to be selected as reliable workhorses for the industry. Of course, technology has advanced over time, creating higher speeds for even greater efficiency, while maintaining high levels of performance and reliability.
Probe, a supplier of cased-hole logging and advanced monitoring technology to the global oil and gas and geothermal industries, has launched the ProMAC, a new series of multi-arm caliper tools. Designed to increase measurement accuracy, reliability and maintainability, ProMAC series tools offer the most advanced measurements in the industry to provide an accurate profile of the internal surface of tubing, casing and completion assemblies.
Schlumberger has introduced the TerraSphere high-definition dual-imaging-while-drilling service at SPE Offshore Europe Conference and Exhibition.
Orbital Gas Systems has received orders to supply GasPTi systems for deployment across multiple natural gas plants by one of the largest U.S.-based producers and transporters of energy. These orders, part of a nascent, ongoing roll-out of GasPTi across the customer's extensive natural gas assets, will be utilized to deliver operating and environmental improvements and practically eliminate ongoing costs associated with maintenance and natural gas consumption at certain customer facilities.
Husky Energy has commenced production at its Dee Valley thermal project in Saskatchewan, the second of six 10,000-barrel-per-day thermal bitumen projects to be brought onstream from 2018 to 2022.
After a major operator recovered from stuck pipe by severing its drill string in just one hour, operators are increasingly adopting the HyPR HoleSaver as their primary contingency against stuck pipe, reports Churchill Drilling Tools, a global oilfield service company specializing in drilling innovation.
In the power production or oil and gas industries, centrifugal pumps for fire protection or condensate systems and other large pumps are critical to operations. However, when unprotected, these units are at greater risk. Operation of these pumps below the minimum flow condition, specified by the manufacturer, can cause overheating—wreaking catastrophic damage to a pumping station. A twin threat, cavitation, can also occur because of operation below the minimum flow condition. These consequences are likely to reduce plant productivity and profitability. The standard pump protection solution, a control valve, offers only complicated functionality and limited economy for installation. For many large pump applications, an all-in-one automatic pump protection valve proves more effective and efficient when compared to a control valve alternative.
Like snowflakes and human fingerprints, no two oil wells are exactly the same. Even though they may be located on adjacent plots of land, the characteristics of the wells can be vastly different. Whereas one might have a straight, unencumbered path to the product reservoir, the second's drilling route may require a number of dogleg turns to avoid difficult rock and sediment formations, which can give the final wellbore the look of a corkscrew.
Wild Well Control, Inc., a Superior Energy Services company and a global leader in well control and engineering services, has added a new 10,000 psi-rated capping stack to its WellCONTAINED group of subsea containment equipment.
Rival Downhole Tools (Rival), a portfolio company of EV Private Equity, has secured a five-year collaborative supply agreement for drilling motors for US Land from a major oilfield services provider. Rival will utilize its market-leading engineering and operational capabilities to support the customer's substantial and growing directional drilling business. Rival will also accelerate the growth of its operational footprint into multiple basins to optimize its proximity to drilling activity.
Following an extensive investigation, flow line repairs, integrity testing and approval of the Canada-Newfoundland and Labrador Offshore Petroleum Board (C-NLOPB), Husky Energy will resume production from the remaining two drill centres shut in following the November 2018 oil spill offshore Newfoundland and Labrador. Husky will now begin an orderly restart and expects to reach full rates by early next week.
CAS DataLoggers provided the data acquisition solution for MTS Solutions, an oil field service company headquartered in Bakersfield, California. MTS has been providing well stimulation services in California for over 30 years, maximizing production for clients using both traditional and green products. Data Acquisition Operations Engineer Kevin England explains, "We're a small business 25-man crew, as opposed to a multi-national company, so we needed a cost-effective monitoring solution for our jobs that still had the advanced functionality our customers require."
Baker Hughes announced that the Baker Hughes Rig Count for the U.S. is down 8 rigs from last week to 934, with oil rigs down 6 to 764, gas rigs down 2 to 169, and miscellaneous rigs unchanged at 1. This is the tenth straight week that the American rig count has declined,
Single Phase Power Solutions, the world's only manufacturer of high horsepower single phase electric motors, match their motors to a pump to provide instant productivity. Available from 30 to 100 HP these single phase pump solutions are easily installed by simply connecting to available single phase utility power - they do not require a phase converter or Variable Frequency Drive (VFD). The company incorporates their Belle Single-Phase MotorT which uses Written-PoleR technology to power standard suction end centrifugal pumps, rotary gear pumps, and turbine pumps in both horizontal and vertical configurations. These pump solutions are ideal for irrigation, drinking water distribution, well pumps, aquifer management, water treatment, wastewater pumping, wastewater collection, wastewater treatment and discharge, and other water and wastewater processing applications. With expertise in pump systems design and manufacture, Single Phase Power Solutions team helps determine the correct materials and style of pump to suit specific application requirements.
CIRCOR International, a worldwide manufacturer of valves for the power generation, industrial, marine and oil and gas markets for over a century, features high-quality R.G. Laurence on/off control valves for applications demanding rapid opening and sealed closure. ATEX-certified and Factory Mutual-approved R.G. Laurence valves offer reliable performance in high temperature and extreme service conditions.
Baker Hughes, a GE company announced that the Baker Hughes international rig count for July 2019 was 1,162, up 24 from the 1,138 counted in June 2019, and up 165 from the 997 counted in July 2018. The international offshore rig count for July 2019 was 255, up 9 from the 246 counted in June 2019, and up 38 from the 217 counted in July 2018.
RTK, a CIRCOR International brand, and an international leader in the design and manufacture of control valves and actuators, introduces the REflex Quick Change Seat Control Valve with REact 30 DC-PoP smart actuator, a flexible all-in-one solution for noise reduction and high pressure drop applications.
Baker Hughes announced that the Baker Hughes Rig Count for the U.S. is down 4 rigs from last week to 942, with oil rigs down 6 to 770, gas rigs up 2 to 171, and miscellaneous rigs unchanged at 1.
The Petroleum Services Association of Canada (PSAC), in its third update to its 2019 Canadian Drilling Activity Forecast, announced that it is decreasing its forecasted number of wells to be drilled (rig released) across Canada for 2019 from 5,300 (May 2019 revision) to 5,100 wells drilled. PSAC based its updated 2019 Forecast on average natural gas prices of $1.60 CDN/Mcf (AECO), crude oil prices of US$57.00/barrel (WTI) and the Canada-US exchange rate averaging $0.76.
Weir Oil & Gas, an upstream provider of pressure pumping and pressure control equipment and services, has introduced the new SPM Quintuplex Extended Max (QEM) 5000 E-Frac Pump. This pump is the only true continuous-duty electric or gas turbine-capable 5,000-horsepower pump in production today, the company states.
Cenovus Energy Inc. recently reached one billion barrels of cumulative production from its Foster Creek and Christina Lake oil sands facilities in northern Alberta. Cenovus is the first company to produce one billion barrels of oil using steam-assisted gravity drainage (SAGD) technology.
Frac Shack Inc.'s newest innovation, the NG SideKick, is the industry's most sophisticated on-pad gas processing unit that takes in field natural gas and processes it down to a safe and usable state for multiple uses on any location. The SideKick depressurizes, heats, and removes liquids and hydrocarbons from field natural gas to ensure the gas is safe and available for use in any natural gas and bi-fuel engine on a hydraulic fracturing location.
Messer highlights new "Huff 'N Puff" treatment to recharge well stimulation at the Unconventional Resources Technology Conference 2019
At URTeC 2019, Messer is highlighting its RECHARGE HNP, or "Huff ‘n Puff," technology, a proven solution for well production enhancement. Ideal for re-stimulating depleted oil and gas wells, the energized RECHARGE HNP treatment combines the proven enhanced recovery properties of carbon dioxide (CO2) or nitrogen (N2) with the latest in advanced nanoparticle technology from Nissan Chemical. URTeC takes place July 22 – 24 in Denver.
ESG successfully completes commercial test of high-temperature, high-pressure downhole microseismic system for hydraulic fracture monitoring
ESG Solutions has recently completed a successful commercial test of its new HOTSHOT downhole microseismic system in the Eagle Ford shale. HOTSHOT represents ESG's latest commitment to acquiring the highest quality microseismic data. The new downhole system was designed specifically for high-temperature, high-pressure operational environments up to 177°C/350°F and 10,000 psi.
SCHROEDAHL, a CIRCOR International brand and an international leader in pump protection and flow control technology, announces that new, self-modulating TDL Automatic Recirculation Valves (ARVs) are now available in more than 35% lighter cast material. These reliable all-in-one pump protection solutions are designed to keep pumping systems in process, firefighting, refinery, power and chemical applications modulating and running smoothly, without cavitation or overheating.
The Canadian Environmental Assessment Agency has commenced federal environmental assessments for the proposed BHP Canada Exploration Drilling Project and the Tilt Cove Exploration Drilling Project. The two projects are located between 300 and 325 kilometres east of St. John's, Newfoundland and Labrador, in the Atlantic Ocean.
Cleansorb, a provider of patented chemical well treatments that enhance hydrocarbon production for the international oil and gas industry, announced that following a series of successful ORCA for OBM treatments on offshore oil production wells and a water injection well drilled with OBM, increased production and water injectivity have been achieved on behalf of a major operator in the Middle East.
Baker Hughes Rig Count: U.S. - 6 to 969 rigs
- U.S. Rig Count is down 6 rigs from last week to 969, with oil rigs down 1 to 788, gas rigs down 5 to 181, and miscellaneous rigs unchanged at 0.
- U.S. Rig Count is down 90 rigs from last year's count of 1,059, with oil rigs down 75, gas rigs down 13, and miscellaneous rigs down 2.
- The U.S. Offshore Rig Count is up 1 rig to 24 and up 4 rigs year-over-year.
Baker Hughes, a GE company announced that the Baker Hughes international rig count for May 2019 was 1,126, up 64 from the 1,062 counted in April 2019, and up 159 from the 967 counted in May 2018. The international offshore rig count for May 2019 was 240, down 11 from the 251 counted in April 2019, and up 42 from the 198 counted in May 2018.
Schlumberger has introduced the GAIA digital exploration platform at the 81st EAGE Conference & Exhibition. The GAIA platform enables exploration teams to rapidly discover and access basin-scale data and manage their exploration opportunities.
NETZSCH Pumps North America, LLC, experts in solutions designed specifically for difficult pumping applications, will be highlighting its NOTOS multiple screw pumps at the 2019 Global Petroleum Show (GPS), which will be held June 11-13, 2019, at BMO - Calgary Stampede Park, in Calgary, Canada. Visit Booth #1394 to see the NOTOS, which is ideal for pumping everything from light fuel oil to viscous asphalt. Also to be featured are NEMO full service-in-place (FSIP) progressing cavity pumps and TORNADO rotary lobe pumps.
Rotork intelligent full-turn electric actuators have been supplied for upstream shale gas production wells in the USA.
Siemens enters Permian gas processing market with innovative electric-drive centrifugal compression solution
Siemens was recently awarded a contract to provide three residue compression trains for two, 250 million (500 million total) standard cubic feet per day (MMSCFD) cryogenic gas plants in the Delaware Basin. The customer, a key producer in the region and long-term user of reciprocating compression equipment, recognized the benefits of centrifugal compression and looked to Siemens for a fully integrated, turnkey solution that includes compressors, motors, variable frequency drives, and associated process equipment.
ProSep, a technology and service provider for integrated process solutions to the global energy industry, has successfully secured a contract with Aker Solutions to provide two MAX+ ProSalt mixers to Equinor's Heimdal Gas Centre Platform in the North Sea.
Wellbore Integrity Solutions (WIS), an affiliate of private equity firm Rhône Capital, and Schlumberger jointly announced that they have entered into an agreement for WIS to acquire the businesses and associated assets of DRILCO, Thomas Tools, and Fishing & Remedial services, along with part of a manufacturing facility located on Rankin Road in Houston, Texas. The transaction is valued at approximately $400 million and is subject to regulatory approvals and other customary closing conditions. The parties expect to close the transaction by year-end 2019.
ITT Inc.'s BIW Connector Systems brand will showcase its enhanced electrical wellhead penetrator solutions for the upstream oil and gas market at the Society of Petroleum Engineers Gulf Coast Section's ESP Symposium May 13-17, 2019 at The Woodlands Waterway Marriott Hotel & Convention Center near Houston, Texas.